What are the 16 steps of blanching?

In life, many people want to have a beautiful hairstyle. Of course, a beautiful hairstyle requires a good hairdresser. Autumn is the season for hairdressing. Many people have the experience of perming and dyeing their hair. Perming or dyeing hair is not as simple as everyone imagines. It is very complicated. If it is too simple, it is easy to damage the hair. What are the 16 steps of hot perm?

Cold perm is a relatively common perm. After perming, you need to use moisturizing gel to maintain the effect. The curls will not look good when dry, and the hair will lose its elasticity after using gel. Hot perm is to soften the hair first and then curl it. The effect of this perm is very good. The curling effect is very good when it is wet or dry, and the curls are soft and elastic. Heat perming changes the structure of the hair, so the effect is more lasting.

Steps of blanching

Step 1: Prepare tools

We need to prepare an electric curling iron and heat it to the appropriate temperature before using it. Too high a temperature will damage the hair.

Step 2: Divide your hair into small sections

Divide your hair into several small sections, then put the curling iron into each section and curl it, keeping it in place for 10 seconds each time.

Step 3: Perm your hair separately

According to the above method, curl all the hair. The whole process takes about 5 minutes.

Step 4: Points to note

During the perming process, divide the hair into as many parts as possible. Perming a small amount will produce better results. If you use a large handful of hair to perm like this, the curls will be uneven, affecting the effect.

Step 5: Finishing

After completing the above four steps, the curls are done. Use your hands to gently loosen your hair so that the curls will be more fluffy. Apply elasticity to the ends of the hair to make the curls more elastic.

Hot perming can also damage the hair. We can strengthen hair care in daily life to reduce damage to the hair. Regularly use hair masks and hair care oils to maintain your hair, which can reduce the phenomenon of dry and frizzy hair, so that the hair quality will be as good as before.

Notes on blanching

1. Improve execution:

Due to the peak season, you may often serve several customers at the same time. You will be very busy and tend to ignore many operational details. Therefore, you must always remind yourself to pay attention to details and do not forget to execute the 16 steps of Irwin hot blanching.

2. Check the hot stamping tools:

During the peak season, there are a lot of customers and often there are not enough tools. Therefore, you may borrow some tools that do not meet the requirements as substitutes. This will violate the principle of hot ironing and lead to unsatisfactory works. So please check whether your cotton paper, clips, bars, tin foil and wool phosphorus reducing milk are sufficient and replenished in time.

3. Details that are easy to overlook:

1. Water temperature:

Due to the large number of customers, the store's hot water is often in short supply, and only warm water or even cold water can be used for flushing. This results in the softening product not being rinsed cleanly, resulting in dry, frizzy and loose curls after perming. Therefore, please prepare a plastic basin and electric kettle. When the water temperature is not enough, use the remaining hot water in the basin to rinse and soak your hair. Pay special attention to the following three steps: flushing before softening, flushing after softening, and texture repair. The water temperature must be 45-50 degrees in winter, and the water temperature of the three must meet the requirements.

2. Texture repair:

There are two situations that are prone to occur in this step. One is that other repair products are used instead, and the other is that the water temperature is too low. These two points will easily cause problems such as dry hair, frizzy hair, poor glossiness, and curls that easily become straight after perming. Therefore, do not change products easily. In addition, the water temperature used for repair soaking should be 50 degrees in winter.

3. Cutting problem:

Cutting determines the final effect of the permed hairstyle. Insufficient cutting space will easily lead to visual impermanence, dryness and frizziness, and loose curls. Therefore, for the curly space, Irwin Hot Perm recommends that you use both equal layers and gradual layers for trimming. Don't let the guests or yourself ignore reasonable cutting.

4. Problems with the upper bar:

The application of hair irons and heating play a decisive role in the natural drying and shaping of the hydrogen bonds during hot perm. However, due to the busy work pace and the fast speed of application of hair irons, people often overlook the problems of not drying the hair before application of hair irons, too much or too little moisture control, and uneven application of hair irons. Here we remind everyone to refer to the 8 requirements of application of hair irons in time to do a good job of hydrogen bonding. (Thickness, moisture, angle, paper selection, bar selection, hair type, strength, number of turns)

5. Heating problem:

During the peak season, many hairstylists usually serve multiple customers at the same time, so they ignore the startup and shutdown process, resulting in the temperature being too high or too low, causing the hair to be dry and scattered and lack texture. Therefore, you need to communicate with your perm and dye artist about the heating process in time and let him help you monitor the temperature.