How to inspect the installed wooden door? What are the requirements for the inspection of the installed wooden door?

We all know that wooden doors are a common type of door. They are made of many materials and have different decoration effects. Many people install wooden doors in their homes. After installing wooden doors, they usually need to be inspected. So how to inspect the wooden doors after they are installed? Let's take a closer look!

How to inspect the wooden door after installation

1. Acceptance of wooden door panels

Check what kind of board is used for the wooden door, whether the quality is up to standard, whether the board meets environmental protection standards, whether the model and brand are consistent with the original order. Check whether the board is "not the same as the one", and whether the size and thickness are cut corners.

2. Wooden door surface

Check whether the surface of the wooden door is smooth and flat, and whether there are any damages, warping, hollows, etc.

Knock it with your hand and listen to see if the sound is crisp and there are any hollows. Touch it with your hand to feel whether the surface is smooth and flat, and whether there are any uneven bumps. Look with your eyes to see if there are any damages, cracks, and whether the edges are tightly sealed.

3. Wooden door installation quality acceptance

Use a ruler to measure whether there is any tilt, whether the installation height and width meet the standards and requirements, and whether the gap on the edge is too large or too narrow.

4. Hardware acceptance

Check whether the hardware accessories are rusty and whether they are flat and smooth. Listen for any unusual sounds when the wooden door is opened and closed. Feel whether the wooden door opens and closes smoothly.

Tips:

Of course, you can also conduct acceptance according to these 7 aspects: 1. Door frame 2. Door leaf 3. Door lock 4. Opening and closing 5. Handle 6. Door shaft 7. Accessories.

Tips for wooden door acceptance

1. Look

①Look at the appearance of the wooden door

Observe the entire appearance of the wooden door to see if there are bubbles or obvious quality problems, whether there is any damage, and whether the color and material of the wooden door and door frame are the same.

② Check whether the wooden door is vertical

During acceptance, pay attention that the wooden door and door frame should be vertical and not deformed. The two should match each other. After installation, they should fit together without any gaps.

2. Knock

Knocking on the side panel of the door frame is mainly to check whether the door frame is hollow and has no bends. If there is a hollow sound, it proves that the wooden door is not installed firmly and accidents are prone to occur later.

3. Use

The process of opening and closing the door should be smooth, and the door hinges should be installed firmly. Finally, check whether the door opens in the correct direction.

Standards for wooden door acceptance

The acceptance standards for wooden doors are mainly divided into hardware acceptance, wooden door surface acceptance, installation acceptance, etc.

⒈Hardware acceptance content

①Are the door locks, hinges, and door stops the same as those purchased?

②Can the door handle rebound normally when pressed down?

③ Whether the lock body guide plate placed inside the door leaf is level with the door leaf.

④ Check whether the lock tongue can be normally buckled into the hole of the door sleeve when closing the door.

⒉Wooden door surface acceptance content

① Check whether the surface of the door frame and door leaf has any scratches, collisions or other external injuries.

② Check whether the color of the wooden door is consistent with the original one purchased and whether there is any serious color difference.

③ Check whether there is paint, sand, wrinkles, etc. on the surface of the wooden door.

④Are the colors of both sides of the door consistent?

⒊ Installation acceptance content

① Check whether the door leaf and sealing strip are tight after closing the door.

② Is the door closed smoothly? No sense of lag.

③ The gaps around the door leaf should be consistent, especially the distance between the door leaf and the ground should not be too high.

④The wooden door cannot be opened and closed automatically. Under normal circumstances, it will stop where it opens to.

⑤The installed wooden door cannot be tilted but should be square.

⑥The door frame is fixed to the wall with screws, but it seems to be useless at present. Most of them are fixed with foam machines.